Sex

ASTM D5856 PDF

Test Method for Determination of Hydraulic Conductivity of Porous Material Using a Rigid-wall Compaction-Mold Permeameter. Start. Standard ASTM standard · ASTM D Status: Withdrawn · Replaced by: ASTM D Soil and Rock (I): D – D (ASTM VOL ). ASTM D Standard Test Method for Measurement of Hydraulic Conductivity of Porous Material Using a Rigid-Wall, Compaction-Mold.

Author: Vojin Mugami
Country: France
Language: English (Spanish)
Genre: Software
Published (Last): 23 December 2005
Pages: 497
PDF File Size: 18.10 Mb
ePub File Size: 20.93 Mb
ISBN: 967-4-89548-786-7
Downloads: 94672
Price: Free* [*Free Regsitration Required]
Uploader: Vur

The problem tends to be of minimal significance for materials that swell when exposed to water for example, compacted, clayey soils but can be a very serious problem for materials that might tend to shrink and pull away from the walls of the permeameter.

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. You must asm logged in to sign up for monitoring You must be logged in to sign up for subscription.

ASTM D5856 – 15

The printed version is available at half price when you buy the electronic version. However, this test method is only intended to be used when water is the permeant liquid.

Atsm or password invalid. Continue shopping Proceed to checkout. It is not possible to buy in the shop – please contact us.

Please choose number of devices you want to open the document on.

  FT-8900R MANUAL PDF

Du abonnerer allerede dette emne. Therefore, the results should be applied to field situations with caution and by qualified personnel. The hydraulic conductivity of compacted materials that have hydraulic conductivities greater than 1?

By tradition in U. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

In cases where it is essential to saturate the test specimen fully with water, the compacted specimen may be tested using Test Method D However, this test method does not ensure complete saturation of the test specimen with water. It was not possible to unsubscribe – please try again later or contact the Danish Standard Please make sure you are logged in.

Users of this standard are cautioned that compliance with Practice D does not in itself ensure reliable results. This test method applies to porous materials containing little or no air.

Asgm results depend on many factors; Practice D provides a means of evaluating some of those factors. Permeation with other liquids, such as chemical wastes, can be accomplished using procedures similar to those described in this test method.

Link to Active This link will always route to the current Active version of the standard. Are you sure you want to unsubscribe?

ASTM D Standard

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applic. However, when the hydraulic gradient acting on a test specimen is changed, the state of stress will also change, and, if the specimen or pore fluid is compressible, the volume of the test specimen or pore fluid will change.

  D.M.329 04 TESTO PDF

There is a problem adding monitoring – please try again later There is a problem adding the subscription – please try again later. The quality of the result produced by this standard is dependent on the competence of the personnel performing it, and the suitability of the equipment and facilities used.

R5856 venligst Dansk Standard. Activation of monitoring failed – please try again later or contact us. By tradition in U. Experience has sometimes shown that flow patterns in small, d58566 test specimens do not necessarily follow the same patterns on large field scales and that hydraulic conductivities measured on small test specimens are not necessarily the same as larger-scale values.

Activation of your subscription failed – please try again later or contact us. The test method is designed to minimize the amount of air in the test specimen. Are you sure you want to unsubscribe monitoring?

Test Method D is recommended astn any material that tends to shrink when exposed to the permeant liquid. Do not show this again. Historical Version s – view previous versions of standard.